E M E INC - NADCAP Approved
90050010
Manufacturer
431 E. Oaks St
COMPTON, CA 90221-1001 United States
Phone: 3106391621
Fax: 310-639-8559
Selected sector: AS
Back
Printable View
Export To Excel
Specification
ProcessDescription
Category
29259-18
Fluorescent Penetrant Inspection
Non-Destructive Testing
Limits:
None
29259-24
Magnetic Particle Inspection
Non-Destructive Testing
Limits:
None
2ZZP00001
Finish Specification for F-35 Weapon System. Note* Approval for this specification is required in conjunction with MIL-PRF-8625 for appropriate anodize seal requirements
Limits:
This spec shall be used in conjunction with MIL-PRF-8625 for appropriate anodize and sealing type
ACS-PRS-1053
Process Specification for Etching Prior to Penetrant Inspection
Chemical Processing
Limits:
None
ACS-PRS-2204
Cleaning and surface preparation of titanium and titanium alloys
Chemical Processing
Limits:
Approved for Type I and alternate solutions per RC/I BR203650
ACS-PRS-7005
Penetrant Inspection
Non-Destructive Testing
Limits:
None
ACS-PRS-7010
Magnetic Particle Inspection
Non-Destructive Testing
Limits:
None
ACS-PRS-8002
Area Requirements for Composite Fabrication
Composites
Limits:
Limited to paint booth area requirements
AMS 2486
Conversion Coating of Titanium Alloys Fluoride-Phosphate Type
Finishes/Coatings
Limits:
None
AMS 2488
Anodic Coating
Chemical Processing
Limits:
None
AMS 2700
Passivation Treatments for Corrosion-Resistant Steel
Chemical Processing
Limits:
Limited to Types 2, 6, 7, 8
ASTM A380
Cleaning, Descaling, and Passivation of Stainless Steel
Chemical Processing
Limits:
None
ASTM B117
Standard Practice for Operating Salt Spray (Fog) Apparatus
Non-Destructive Testing
Limits:
In-house testing only
ASTM B600
Descaling & Cleaning Titanium and Titanium Alloy Surfaces
Chemical Processing
Limits:
None
ASTM B912
Standard Spec for Passivation of Stainless Steels Using Electropolishing
Chemical Processing
Limits:
None
ASTM E1417
Standard Practice for Liquid Penetrant Testing
Non-Destructive Testing
Limits:
None
ASTM E1444
Standard Practice for Magnetic Particle Testing
Non-Destructive Testing
Limits:
None
F-101
Chemical Conversion Coating for Aluminum
Chemical Processing
Limits:
Limited approval per RCI BR115364.
F-102
Sulfuric Acid Anodic Coatings for Aluminum Alloys
Chemical Processing
Limits:
Limited approval per RCI BR115365.
F-116
Passivating CRES Alloys.
Chemical Processing
Limits:
Passivation solution per para. 3.1.1.1 only
F-152
Applying Dry Film Lubricants
Chemical Processing
Limits:
None
FP-153
Primer MIL-P-85582, Epoxy, Voc Compliant, Application of
Chemical Processing
Limits:
None
FP-28
Chemical Conversion Coatings, Colored, for Aluminum and Aluminum Alloys
Chemical Processing
Limits:
None
GP 17 G
Procedure, Etching prior to Penetrant Inspection
Chemical Processing
Limits:
None
GSS 4306
Integral Fuel Tank Coating (MILC27725) Application of
Chemical Processing
Limits:
None
GSS 4310
Application of Primer Coating, Epoxy Polyamide
Chemical Processing
Limits:
Limited to force cure per RCI BR100306
GSS 4407
Application of Lacquers: Acrylic
Chemical Processing
Limits:
Supplier is utilizing GSS 4510 as an approved substitute
GSS 4510
Coating, Polyurethane, Application of
Chemical Processing
Limits:
None
GSS 7021
Acid Cleaning of Ferrous Alloys
Chemical Processing
Limits:
None
GT 23 A
Fluorescent Penetrant Inspection
Non-Destructive Testing
Limits:
None
LMA-PC009
Hardness and Conductivity Testing
Miscellaneous
Limits:
None
LMA-PC201
Fluorescent Penetrant Inspection of Metallic Parts & Materials
Non-Destructive Testing
Limits:
Facility requalification for Supplier to inspect F-35 Critical Parts as defined in LMA-PC201, was done on 07/09/2024. Two (2) inspectors were tested and passed: Joe Lipsey – Employee # 133, Stamp # 06 Desmond Handley – Employee # 165, Stamp # 13. Procedure number used was SMPP #74 LMA-PC201, Revision F, dated 07/12/2024. This procedure was updated during the course of the demo and validated at that time. Due Date for next facility requalification: 07-2027
LMA-PG001
Etch/Cleaning Prior to Penetrant Inspection
Chemical Processing
Limits:
Approved for aluminum , titanium, CRES and Nickel alloys. Approved procedures, SMPP 03-LMA1- TI, SMPP 03-LMA1-AL. SMPP 03-LMA2-PG101-PH , SMPP 03-LMA2-PG101-NI
LMA-PH016
Conversion Coating of Titanium Alloys
Chemical Processing
Limits:
Limited to using the MIL-DTL-5541 conversion process only
LMA-PJ264
Application and Control of Organic Finishes
Chemical Processing
Limits:
None
MIL-DTL-5541
Chemical Conversion Coatings for Aluminum and Aluminum Alloy
Chemical Processing
Limits:
Limited to Type 1 only
MIL-F-18264
Finishes Organic, Weapons System, Application and Control of
Chemical Processing
Limits:
None
MIL-PRF-46010
Dry Film Lube Superseded by AS5272 for Ty I & II only
Chemical Processing
Limits:
None
MIL-PRF-46147
Lubricant, Solid Film, Air Cured (Corrosion Inhibiting)
Chemical Processing
Limits:
None
MIL-PRF-8625
Anodic Coatings For Aluminum and Aluminum Alloys
Chemical Processing
Limits:
5% sodium or potassium dichromate seal is required when Mil-PRF-8625, Type II anodize is called out on C-2, E-2C/D, EA-6B, EA-18G or E-8 (Jstars) engineering drawings
MPD 1074
Cleaning of Aluminum Alloy Parts
Chemical Processing
Limits:
RCI approved for deviation of Method III-B and III-C
MPD 1103
Cleaning of Titanium and Titanium Alloys
Chemical Processing
Limits:
Approved RC/I R420106 for alternate etch solutions
MPD 1183
Pickling of Precipitation-Hardening Steel
Chemical Processing
Limits:
None
NGT23K
Magnetic Particle Method of Inspection for Non-Destructive Test
Non-Destructive Testing
Limits:
None
T-103
Penetrant Inspection
Non-Destructive Testing
Limits:
None
T-104
Magnetic Particle Inspection
Non-Destructive Testing
Limits:
None