| Specification | ProcessDescription | Category | SpecLimits |
| ACS-PRS-1053 | Process Specification for Etching Prior to Penetrant Inspection | Chemical Processing | Limits: None |
| ACS-PRS-1151 | Welding of Tubular Joints | Welding | Limits: None |
| ACS-PRS-2004 | Structural Adhesive Bonding with Epoxy Paste Adhesive | Composites | Limits: Room temperature cure only |
| ACS-PRS-2151 | Process Specification for Sealing, Integral Fuel Tank and Fuel Cell Cavity | Finishes/Coatings | Limits: Limited to Pre-measured sealant dispensing cartridges (Sem kits) |
| ACS-PRS-2204 | Cleaning and surface preparation of titanium and titanium alloys | Chemical Processing | Limits: Limited to Type 1 process; Oxide removal from titanium and titanium alloy surfaces limited to Scuff Sanding and/or Grit Blasting; Excludes BAMS Program |
| ACS-PRS-4504 | Assembly of Threaded and Welded Fittings. *NOTE* ASPL approval is not required for assembly of Class A Threaded Connections. Qualification and ASPL approval is required for Class B Welded Connections. | Miscellaneous | Limits: None |
| ACS-PRS-5001 | Curing Procedures for Composite Laminates and Sandwich Assemblies | Composites | Limits: None |
| ACS-PRS-5012 | Process Specification for Wet Layup of Composite Laminates and Foam Sandwich Structures | Composites | Limits: Limited to Type IV process only. Limited to non-critical, non-structural wet lay up |
| ACS-PRS-5012.04 | PROCESS SPECIFICATION FOR WET LAYUP OF CARBON FABRIC FIBERGLASS FABRIC OR COPPER MESH ON CURED COMPOSITE SURFACES | Composites | Limits: Limited to noncritical, nonstructural wet lay up |
| ACS-PRS-5017 | Process Specification Fabrication of Out-of-Autoclave, 350°F Cure, Epoxy Laminates | Composites | Limits: None |
| ACS-PRS-5018 | Process Specification for Fabrication of Pi Joint Composite Structures Utilizing 350°F Curing Out-of-Autoclave Materials | Composites | Limits: None |
| ACS-PRS-5018.02 | Process Specification For Fabrication Of Current Carrying PI Joint Structures For Lightning Arc Mitigation | Composites | Limits: Limited to Method 1 |
| ACS-PRS-5020 | Specification for Out-of-Autoclave Fiber Placed Carbon Epoxy Laminates, Fabrication and Acceptance of | Composites | Limits: None |
| ACS-PRS-5053 | Machining of Nonmetallic Honeycomb Details | Composites | Limits: To ‘Repairs’ Only |
| ACS-PRS-5065 | Process Specification for Fabrication Of 350°F Curing Out-Of-Autoclave Epoxy Composite Structure, Bonded, Cocured, Or Cobonded | Composites | Limits: None |
| ACS-PRS-5065.02 | Installing Inserts, Hardpoints, and Edge Filler in Composite Sandwich Structure | Composites | Limits: None |
| ACS-PRS-6002.01 | Process Specification for Contamination Free Hole Preparation, Drilling, Machining and Trimming of Composites and Composite/Metallic Structures | Composites | Limits: None |
| ACS-PRS-7001 | Ultrasonic Inspection of Composites and Bonded Assemblies | Non-Destructive Testing | Limits: None |
| ACS-PRS-7003 | Eddy Current Inspection for Defects | Non-Destructive Testing | Limits: None |
| ACS-PRS-7005 | Penetrant Inspection | Non-Destructive Testing | Limits: Excludes Appendices |
| ACS-PRS-7101 | Non-Destructive Inspection of Composite Structures | Non-Destructive Testing | Limits: None |
| ACS-PRS-8002 | Area Requirements for Composite Fabrication | Composites | Limits: None |
| ACS-PRS-8002.01 | Process Specification for Area Requirements for Adhesive Bonding and Composite Fabrication of PI, Green Tie and Splice Joint Primary Structures (Controlled Bonding Area) | Composites | Limits: None |
| AMS 2770 | Heat Treatment of Wrought Aluminum Alloy Parts | Heat Treat | Limits: None |
| AMS 2801 | Heat Treatment of Titanium Alloy Parts | Heat Treat | Limits: Stress Relief only. Limited to vacuum furnaces 21B, 58B, and 059F |
| AWS D17.1 | Fusion Welding for Aerospace Applications | Welding | Limits: Limited to GTAW process; Material Groups VI |
| MIL-DTL-5541 | Chemical Conversion Coatings for Aluminum and Aluminum Alloy | Chemical Processing | Limits: Type 1 only |