| Specification | ProcessDescription | Category | SpecLimits |
| ACS-PRS-2001 | Structural Adhesive Bonding with Epoxy Film Adhesive | Composites | Limits: None |
| ACS-PRS-2004 | Structural Adhesive Bonding with Epoxy Paste Adhesive | Composites | Limits: None |
| ACS-PRS-2151 | Process Specification for Sealing, Integral Fuel Tank and Fuel Cell Cavity | Finishes/Coatings | Limits: Not Approved for Appendix “A” Limited to pre-measured sealant dispensing cartridges (Semkits) |
| ACS-PRS-2201 | Surface Preparation for Structural Adhesive Bonding | Chemical Processing | Limits: Limited to Type I only |
| ACS-PRS-2201.01 | Surface Preparation for Structural Adhesive Bonding, Composites | Composites | Limits: None |
| ACS-PRS-4101 | Fabrication of Wire Harnesses | Miscellaneous | Limits: Limited to MRB repairs only |
| ACS-PRS-5001 | Curing Procedures for Composite Laminates and Sandwich Assemblies | Composites | Limits: |
| ACS-PRS-5012 | Process Specification for Wet Layup of Composite Laminates and Foam Sandwich Structures | Composites | Limits: Limited to Type IV ONLY Not Approved for Appendix “A” |
| ACS-PRS-5012.04 | PROCESS SPECIFICATION FOR WET LAYUP OF CARBON FABRIC FIBERGLASS FABRIC OR COPPER MESH ON CURED COMPOSITE SURFACES | Composites | Limits: Excludes Appendix A |
| ACS-PRS-5017 | Process Specification Fabrication of Out-of-Autoclave, 350°F Cure, Epoxy Laminates | Composites | Limits: Not Approved for Appendix “A”. |
| ACS-PRS-5018 | Process Specification for Fabrication of Pi Joint Composite Structures Utilizing 350°F Curing Out-of-Autoclave Materials | Composites | Limits: |
| ACS-PRS-5018.02 | Process Specification For Fabrication Of Current Carrying PI Joint Structures For Lightning Arc Mitigation | Composites | Limits: None |
| ACS-PRS-5053 | Machining of Nonmetallic Honeycomb Details | Composites | Limits: Not Approved for Appendix A |
| ACS-PRS-5065 | Process Specification for Fabrication Of 350°F Curing Out-Of-Autoclave Epoxy Composite Structure, Bonded, Cocured, Or Cobonded | Composites | Limits: |
| ACS-PRS-5065.02 | Installing Inserts, Hardpoints, and Edge Filler in Composite Sandwich Structure | Composites | Limits: Limited to Type I, II & V only |
| ACS-PRS-6002 | Hole Preparation, Drilling, Mach.,Trimming for Composite/Metallic Structure | Composites | Limits: Not Approved for Appendix A, B & C |
| ACS-PRS-6002.01 | Process Specification for Contamination Free Hole Preparation, Drilling, Machining and Trimming of Composites and Composite/Metallic Structures | Composites | Limits: None |
| ACS-PRS-7001 | Ultrasonic Inspection of Composites and Bonded Assemblies | Non-Destructive Testing | Limits: Limits; Not approved for Appendix A & B |
| ACS-PRS-7101 | Non-Destructive Inspection of Composite Structures | Non-Destructive Testing | Limits: |
| ACS-PRS-8002 | Area Requirements for Composite Fabrication | Composites | Limits: Not approved for Appendix A & B |
| ACS-PRS-8002.01 | Process Specification for Area Requirements for Adhesive Bonding and Composite Fabrication of PI, Green Tie and Splice Joint Primary Structures (Controlled Bonding Area) | Composites | Limits: |